E-Tech ET8 Instrukcja Instalacji Pobierz pdf (Strona 56)

E-TECH RADIO

E-TECH ET8 (V4) CONTROL PANEL – INSTALLER MANUAL

RADIO DEVICE PROGRAMMING

Each of the 8 zones of the ET8 can be a radio zone. Once programmed, zones

can accept both Radio Devices and normal zone inputs simultaneously.

The optional 100–200 E-Tech Radio Interface is required for Radio Devices to

operate.

A Radio Device is any type of E-Tech transmitter including Radio PIR, Radio

Reed Switches, Radio Smoke Detector.

PROGRAMMING RADIO DEVICES

Up to 8 Radio Devices can be assigned, (one per zone).

PROGRAMMING SEQUENCE – NO RESTORALS

Suitable for 100–663 Radio PIR, 100–665 Radio Pendant, 100–203 Radio

Smoke Detector.



Select a zone using

P01E – P08EP01E – P08E

P01E – P08E

The ARMED light will be ON if a Radio Device is already programmed to the zone. Press 0E to delete.



Press

1E1E

The READY light will turn ON to indicate that the zone is ready to accept the Radio Device.



Trigger the Radio Device

A. If the Radio Device is accepted, the READY light will turn off, the ARMED light will turn on and 3 beeps

will sound.

B. If the READY light stays on and a warning beep sounds, the Radio Device is already assigned to

another zone and must be cleared from that zone first.

EXAMPLE: To program a Radio PIR on zone 1:

P01E 1E Trigger the Radio PIR (or simply connect the battery)

PROGRAMMING SEQUENCE – WITH RESTORALS

Suitable for 100–662 Radio Reed Switch.



Alarm the reed switch, ie., move the magnet away from the switch

Leave the reed switch in the alarm condition and wait until radio transmission has stopped.



Select a zone using

P01E – P08EP01E – P08E

P01E – P08E

The ARMED light will be ON if a Radio Device is already programmed to the zone. Press 0E to delete.



Press

1E1E

The READY light will turn ON to indicate that the zone is ready to accept the Radio Device.



Restore the reed switch (place the magnet next to the switch)

A. If the Radio Device is accepted, the READY light will turn off, the ARMED light will turn on and 3 beeps

will sound.

B. The MEMORY light will turn on to indicate that this device sends Restorals.

C. If the READY light stays on and a warning beep sounds, the Radio Device is already assigned to

another zone and must be cleared from that zone first.

EXAMPLE: To program a Radio Reed Switch with Restorals on zone 2:

Alarm the reed switch P02E 1E Restore the reed switch

P01E ~ P08E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

No Radio Devices programmed

NOTES:

• Radio Device programming is done by

‘learning’ the code by radio.

• Radio Devices codes can only be deleted

by keypad.

• Some E-Tech Radio Devices send

separate Alarm and Restore signals.

• E-Tech Radio Keys (100–664), can also

be programmed to operate on radio

zones, but they are normally used to

operate Radio Codes as described on

page 57.

• Late model E-Tech Radio PIRs (100–663)

and Radio Reed Switches (100–662)

send Supervision signals.

SUPERVISION RELATED OPTIONS:

P65E Supervised Radio Zones

P66E 1E–8E Radio Supervision Alerts

P67E Radio Supervision Time

P75E 12E Radio Supervision Fail Report

• RELATED OPTIONS:

P09E–P10E Programming Radio Keys

RADIO DEVICES – OPTION TABLE

DELETING A RADIO DEVICE:



Use

P01E P01E

P01E to

P08E P08E

P08E to select the zone



Press

0E0E

0E to clear the device (3 beeps will sound)

TIP: To prevent conflicting radio signals when programming Radio

Devices, disable each device once you have finished programming it.

(Remove the battery or open the RADIO link).

Remember to enable all the devices when programming is completed.

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

E-Tech ET8 Instrukcja Instalacji Strona 56

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa E-Tech ET8